❶ 物理，请问电路中的VCR和VAR分别是什么英文全拼是什么翻译
VCR是Voltage Current Relation的缩写，两端电压u与流经它的电流i之间的关系。
VAR是Volt Ampere Relation的缩写，电压单内位容V，电流单位A，电阻元件的特性称为伏安特性或伏安关系。
❷ 电子电路方面翻译求助
特征
输入电流低
最大输入偏置电流10 pA (B级)
最大补偿电流0.6 pA(B级)
共态抑制比
G=10时，共态抑制比最小100dB(B级)
G=1时，5kHz时共态抑制比最小80dB(B级)
交流特性好，耗能低
带宽1.5 MHz (G = 1时)
输入噪声14 nV/√Hz(1 kHz时)
回转速率2 V/μs
最大供应静态电流750 μA
通用
MSOP封装
Rail-to-rail输出
输入电压振幅低于负供应电压
静电保护4 kV
单一供应电压4.5 V～36 V
双重供应电压±2.25 V ～ ±18 V
单电阻增益(G = 1 to 1000)
应用
医用仪器
获取精密数据
传感器界面
概括描述
第一个单供JFET输入放大器采用MSOP封装的AD8220。根据高性能、便携性仪器的需要设计,AD8220 的最小直流共态抑制比86dB，G=1、5kHz时交流共态抑制比80dB。最大输入偏置电流10pA，工业温度范围内代表值低于300pA。不论JFET输入多少，AD8220仅有10Hz的噪声角。由于混合信号处理的增强效应，各个系统需要的能量需求增加。AD8220是为了减轻这个问题设计的。AD8220可以在±18 V双电压供应或+5 V 电压供应。它的rail-to-rail输出在便携设备低电压供应下获得最大动态范围。在没有双电压供应时能在单边5V电压下工作。AD8220最大静态电流750μA，对电池供电的设备来说很理想。
单电阻时增益1～1000。增益增大会增加 common-mode rejection。需要更高共态抑制比的测量 当AD8220设为大增益时有益于阅读小信号。相关针脚允许用户补偿输出电压。这个特征有利于模数转换器界面。MSOP封装的AD8220使SOIC面板面积减少约一半。可工作于工业温度范围?40°C到85°C。
❸ 谁能帮我翻译几个电路图上的专用词语，回答得好加分。
1.CB 控制总来线2.mains isolator 主隔离器3.incoming supply 输入电源4.air conditioner 冷气机自 air fault 空调故障 5.MCCB配电箱 6.suction fan 排气风扇7.doffing motor落纱电机 8.main drive motor 主驱动电机9.brake resistors 制动电阻 10.drive run relay发动继电器 11.spin speed旋转速度 12.false twist drive假捻车道 13.假捻车道电机14.自锁继电器15.启动继电器16.emer stop17.展示门开关18.假捻接触19.主驱动凸轮接触20.故障21.应对凸轮继电器22.开启/释放装置 23.起重电磁铁向上线器
24电磁升降装置25.气压机26.运行小时计时器27.正向控制继电器28.反向控制继电器 29.抗电磁咆哮30.咆哮计时器
❹ 可追加，高分求英文翻译，电路图方面。
这个开关是受汽车的点火钥匙控制的。
关掉钥匙时，同时控制两组电瓶之间的开关相连断开。断开后，XX系统只会从新装的电瓶上取电工作，而不会消耗原车的电量。
当钥匙打开发动车辆时，控制开关接上，发动机又会对新装的电瓶充电。
以此，这样循环工作。
This switch is controlled by the car’s ignition key.
When the key is turned off, the control link between two sets of batteries will be cut off. After being cut off, the xx system shall only work with the power from the newly installed battery instead of the original car battery.
When the car is turned on by the key, the control link will be connected and the engine will recharge the newly installed battery. So, this operation works in cycle.
在新装电瓶与XX系统之间的电路增加一个可以定时断电的电路，作用是司机下班后可以定时关闭XX系统。司机停车熄火后，在我们设定的时间内，可以自动断开新装电瓶与XX系统之间的供电线路，从而保护电瓶不会被耗尽。
司机上班发动车辆时，又会自动把XX系统的电源接通。
A timer controller is added to the circuit between the newly installed battery and the xx system, this is for the driver to set an auto- timing shut-off for the xx system when he’s off ty. After the driver has parked the car and switched off the engine, ring the period preset by us, the power supply from the newly installed battery to the xx system will be cut off, and the power depletion of the battery will be avoided.
When the driver comes back on ty and starts the car, the power supply to the xx system will be reconnected automatically.
❺ 求翻译大神翻译关于电路的句子。不要拿翻译软件忽悠我，谢谢
These constraints require an energy-efficient multiplier that enables low compressor tree
fan-outs
译文：这些约束条件要求有一个有能量效率的乘法器，它可以降低压缩机树杈的散开！
[2]. In this paper, we present a 2’s complement 16-bit multiplier circuit, designed and simulated in a 0.18 µm CMOS process.
译文：在本页上，我们介绍了一个2秒的完整的16位乘法器电路，它被设计和模拟在一个0.18 µm CMOS 处理器中。
❻ 电路翻译问题
找出电路吸收总电量
找出电路产生总电量
❼ 求翻译--电路方面的翻译高手请帮忙
The electric circuit's diagram includes the switch K1, the first electric resistance R1, the second electric resistance R2, the third electric resistance R3, the electric capacity C1, the LED( the Light Emitting Diode, give out light the diode) L1, the first needle feet P1, the second needle feet P2 and provide the power supply V1 of the 3.3 V electric voltage.Among them, say the first needle feet P1, the first electric resistance R1, the switch K1, the third electric resistance R3, the LED L1, the second needle feet P2 carries on establish one by one in order, say the second electric resistance R2 and the electric capacity C1 say merges the conjunction, shoulding merge the conjunction on carrying to link say the first needle feet P1 passes one an on-line of the electric resistance R1, another on carrying to connect the ground.The power supply V1 say connect the switch K1 with the on-line between the third electric resistance R3.The cathode of the LED L1 say link the third electric resistance R3, the anode link the second needle feet P2.The electric capacity C1 cathode say link say the first needle feet P1 passes one an on-line of the electric resistance R1, the anode connects the ground.The switch K1 say return with the input device say 2 medium an importation key conjunction, be press that input device 2 the importation key that should correspond mediumly, the switch K1 close, the first needle feet P1 carry electricity even and high, thus proce the hardware interruption.When the system sends out the high electricity even give the second needle feet P2, because of the LED L1 another on carrying to have the power supply V1 through the electric resistance R3 conjunction, the LED's L1 connects the electric circuit of the place, the LED's L1 has the electric current to pass, for this reason hour the LED's L1 is bright;When the system sends out the low electricity even give the second needle feet P2, in the LED's L1 there is no electric current pass, the LED's L1 of for this reason hour put out;When the system send out high and low interrupted the electricity even give the second needle feet P2, in the LED's L1 interrupteding the electric current to pass, for this reason hour the LED's L1 flicker.
❽ 英语高手帮我翻译一下，关于电路的。
翻译质量可保证，不过太长了，加点分吧？
1 Introction
1.引言
THE USE of conventional, unsymmetrical amplifier circuits in biomedical engineering is very limited, because of their inadequacy in suppressing power-line interference.常规的不对称放大器电路在生物医学工程中的使用是有限的，因为它们在抑制电力线路的干扰上存在不足之处。 Because one of the patient electrodes is directly connected to the amplifier
signal ground and the other is a high impedance point, the interference
current flows only through the grounded electrode. 因为病人的电极中有一个直接连接到放大器信号接地，另一个是高阻抗点，所以干扰电流只流过被接地的电极。The grounded electrode impedance voltage drop is amplified and leads to circuit saturation or masking of the useful biopotential
signal. 该接地电极阻抗的电压降被放大，并导致电路饱和，或者对有用生物电位信号的掩蔽。
Many biosignal acquisition devices could benefit from the use of only two electrodes. 很多生物信号采集装置可以通过仅采用两个电极而得到好处。Electrocardiogram monitoring in intensive care wards, ambulatory monitors, defibrillators etc.
are among the most common examples. 在重症监护病房中的心电图监控、门诊监测器、除颤器等是最常见的例子。
The most widely used technique for biosignal amplification is based on an instrumentation amplifier first-stage design, because of its ability to suppress the common mode interference
(NEUMAN, 1998). 最广泛使用的生物信号放大技术是基于一种仪表放大器的一级设计，因为它能抑制共模干扰（Neuman，1998）In two－electrode instrumentation, the
amplifier inputs must have a differential impedance that is as high as possible to avoid signal attenuation. 在双电极仪器应用中，放大器的输入必须有尽可能高的差分阻抗，以避免信号衰减。On the other hand, the amplifier should have reasonably low common mode impedance, to create a path for the common mode interference
currents without significant voltage drop, keeping both inputs in their specified operating voltage range. 另一方面，放大器的共模阻抗应该合理地低，以便为共模干扰电流创造一个通路而不致有明显的电压降，从而将两个输入都保持在它们规定的工作电压范围内。
THAKOR and WEBSTER (1980) introced a bootstrapped input stage. However, it has an inctive common mode input impedance, resulting in a very poor common mode
input current range, especially for higher frequencies. Thakor和Webster（1980）引入了一个自举（bootstapped）输入级，产生了很差的输入共模电流范围（特别是在较高的频率下）
A circuit for a two-electrode, non-differential amplifier was developed (DOBREV, 2002), the performance of which isquasi-equivalent to the differential amplifier described by DOBREV and DASKALOV (2002). Dobrev于2002年开发了一种用于双电极、无差动放大器的电路，其性能准-等效于Dobrev和Daskalov（2002）所描述的差分放大器。
Because the body as signal
source is floating and, in addition, the modern biopotential amplifiers are isolated, it is possible to drive actively one of the electrodes to the circuit common potential and thus to
balance the flowing interference currents. 因为作为信号源的人体是浮动的，而且现代的生物电位放大器是隔离的，所以有可能主动地将电极中的一个激励到电路的公共电位，并因此来平衡流过的干扰电流。
Now, a very simple, low-cost circuit of a two-electrode nondifferential
amplifier is suggested, where the interference current balancing is achieved by one operational amplifier
(OA) and two parallel RC networks.现在人们提出了一种很简单而又廉价的双电极、无差动放大器的电路，其中，干扰电流的平衡是靠一个运算放大器（OA）和两个并联的RC（阻容）网络实现的。
❾ 求电路高手翻译，急啊！万分感激！
在这个报道发布基于客户投诉收到你的ACKE电力机车车间,建立了一系列的行动的范围之内。
1。在不同的征收控制相位的线圈去看看确切的尊重的卷线张力和转速的卷线轴上。特别注意也被执行在锡焊操作,包括控制,为正确的温度的焊接。
2。四个方面的电阻测量控制的线圈本身一旦线圈是完整的,所以它扩展到每一件了。这是除了最后的工厂测试完成后在每个接触器总成。
3。人才培养的具体操作和储存这些线圈的储藏室,特别关心进货有条不紊,避免拳法或过度负荷条件下,由于线圈层叠加在同一个垃圾桶。线圈将放置在层,每卷好与其他以避免刮在处理和/或运输。
它也被建立,可立即隔离任何线圈已经下降或接收吹在处理,在一个受控的方式为额外的控件或拒绝。
4。定期审核生产流程的桥式整流/馈电设置和给予特别关注的内部开关。
5。特殊的培训人员的组装桥式整流/馈电设置为了得到最大的护理工作区域的整洁,以避免所有的污染和塑料部分内部开关的内部开关触点被安装。
垃圾箱也被关闭了的长袜和处理内部开关接触和塑料零件,以排除最终灰尘的污染。
6。介绍一种新的检测的桥式整流/馈电开关操作条件设定为内部装配之前
❿ 求助电路图专业词翻译,急急急!!!
电源应该是power source或powersource或power supply
供电点---power supply point
进板-----importation
出板-----exportation
照明-----lighting，illumination
插座-----socket
马达-----motor
照明指示-lighting indicator
插座指示-socket indicator
24V指示--24V indicator
运行指示-running indicator
电源指示-supply indicator
照明开---lighting on
插座开---socket on
24V开----24V on
马达开---motor on
照明关---lighting off
插座关---socket off
24V关----24V off
马达关---motor off
可编程控制器----programable logic controller
面板-----operating panel